How to Change the Oil on a Cub Cadet Riding Lawn Mower

How to Change the Oil on a Cub Cadet Riding Lawn Mower

Regular oil changes are essential to keeping your mower’s engine in working condition and will maximize its lifespan. To keep your Cub Cadet running smoothly and efficiently, follow these steps to change the oil in your machine.

Before performing any maintenance on your , refer to your owner’s manual for recommended maintenance and safety information. Maintenance instructions vary by model, so depending on your riding lawn mower model our instructions may vary slightly. Check your owner’s manual to get instructions specific to your model, including information about the recommended oil type.

Begin by parking your mower on a flat, level surface. Turn the engine off and allow it to cool, remove the ignition key, disconnect the spark plug ignition wire to prevent accidental starting, and engage the parking brake.

Place a piece of cardboard under your mower to catch oil drips and use an oil basin to catch the old oil when it is drained from the engine.

Remove the dip stick from the oil fill tube and drain the oil and allow the engine oil to completely drain. If your Cub Cadet has an oil filter, replace it with a new one. Use an oil filter wrench to unthread the oil filter from the engine. Use a rag to clean the area around the engine of any spilled oil.

Replace the oil filter and add a little oil to the seal of the new oil filter to help with the install. Use your hand to thread the new oil filter onto the engine. Do not overtighten. Use your oil filter wrench to snug the fit but do not overtighten.

Add new oil to your Cub Cadet riding lawn mower. Use the oil recommended by the engine manufacturer and fill to the recommended levels. Replace the dip stick and check the engine oil levels.

Check the oil level with the dip stick. Depending on where it reads, you may need to add more oil. When checking the oil with the dip stick, place the dip stick into the oil and push it all the way down. Remove the dip stick, clean it with your rag, and place it in the oil one more time to check the oil level.

Reconnect the spark plug wire and your maintenance is done.

Use our illustrated parts diagrams to locate any replacement parts you may need for maintenance.

Free Parts Search      Free Shipping

How to Change the Air Filter on a Cub Cadet Riding Lawn Mower

How to Change the Air Filter on a Cub Cadet Riding Lawn Mower

To ensure that your engine runs smoothly this season and the next, regularly clean or replace the air filter on your Cub Cadet riding lawn mower. It’s recommended that your air filter be cleaned or replaced every 50 hours of use. In dry, dusty conditions this should be done more frequently.

Before performing any maintenance on your Cub Cadet riding lawn mower, refer to your owner’s manual for recommended maintenance and safety information. Maintenance instructions vary by model, so depending on your riding lawn mower model our instructions may vary slightly. Check your owner’s manual to get instructions specific to your model.

Begin by parking your mower on a flat, level surface. Turn the engine off and allow it to cool, remove the ignition key, disconnect the spark plug ignition wire to prevent accidental starting, and engage the parking brake.

Use a rag to clean the engine of dirt and debris. Remove the air filter cover and the air filter.

Check and clean the air filter. Remove the foam pre filter. Use a flashlight to check for any damage to the air filter. Clean the paper element filter by tapping gently to remove dust. If the element is very dirty or damaged, replace it with a new one.

Wash the foam pre filter. Use mild detergent and warm water to wash the foam pre filter and allow it to dry completely. Keep in mind – never use gasoline or low flash-point solvents for cleaning the air filter elements.

Place the dry pre filter back onto the air filter and reinstall the air filter. Secure the air filter cover and lock handles.

Reconnect the spark plug ignition wires on your Cub Cadet riding lawn mower.

Use our illustrated parts diagrams to locate any replacement parts you may need for maintenance.

Free Parts Search      Free Shipping

How to Change the Oil on a Cub Cadet Ultima

How to Change the Oil on a Cub Cadet Ultima

Regular oil changes are essential to keeping your Cub Cadet Ultima’s engine in working condition. Regular oil changes also maximize the lifespan of your mower and keep your Cub Cadet running smoothly and efficiently.

Before performing any maintenance on your Cub Cadet Ultima, refer to your owner’s manual for recommended maintenance and safety information. Maintenance instructions vary by model, so depending on your model our instructions may vary slightly. Check your owner’s manual to get instructions specific to your model, including information about the recommended oil type.

To change the oil on your Cub Cadet Ultima, begin by parking your mower on a flat, level surface. Turn the engine off and allow it to cool, remove the ignition key, disconnect the spark plug ignition wire to prevent accidental starting, and engage the parking brake.

It may be helpful to place a piece of cardboard under your mower to catch oil drips. Use an oil basin to catch the old oil when it is drained from the engine. Remove the dip stick and drain the oil. Use a ¾-inch and a ½-inch wrench to unthread the stopper plug from the oil outlet and allow the engine oil to completely drain. After the oil has drained, secure the stopper plug to the oil outlet.

Replace the oil filter with a new one. Use an oil filter wrench to unthread the oil filter from the engine. Use a rag to clean the area around the engine of any spilled oil.

Replace the oil filter and add a little oil to the seal of the new oil filter to help with the install. Use your hand to thread the new oil filter onto the engine. Do not overtighten. Use your oil filter wrench to snug the fit but do not overtighten.

Add new oil to your Cub Cadet Ultima. Use the oil recommended by the engine manufacturer and fill to the recommended levels. Replace the dip stick and check the engine oil levels.

Check the oil level with the dip stick. Depending on where it reads, you may need to add more oil. When checking the oil with the dip stick, place the dip stick into the oil and push it all the way down. Remove the dip stick, clean it with your rag, and place it in the oil one more time to check the oil level.

Reconnect the spark plug wire on your Cub Cadet Ultima.

Use our illustrated parts diagrams to locate any replacement parts you may need for maintenance on your Cub Cadet Ultima.

Free Parts Search      Free Shipping

Tips to Prepare your Snow Blower for Winter

Tips to Prepare your Snow Blower for Winter

Whether you’re prepping your snow blower for another year of snow removal or getting your new machine ready for its first winter, these snow blower maintenance tips will help ensure you’re prepared for snow this winter.

Tip #1

Change the oil in your snow blower. This should also be done after the first five hours of use this winter and after every subsequent season.

Old oil can cause problems for your machine’s engine, making it hard to start. If there is old oil, dispose of it properly. There is an oil drain plug in the back of your snow blower. Use a wrench to remove the plug and drain the oil into a container.

Tip #2

Drain old fuel and replace with fresh fuel. Old fuel can cause problems for your blower’s engine, making it hard to start.

Also, consider adding a fuel stabilizer so your fuel stays fresh even if you don’t need to use your snow blower.

Tip #3

Install a new spark plug, if necessary. Check your spark plug at the start of each season.

Disconnect the spark plug lead from the spark plug. Remove the spark plug with a spark plug socket wrench and remove debris from around the spark plug. Examine your spark plug and check for any damage. If there is damage, rust or corrosion on your snow blower’s spark plug, replace the spark plug.

Tip #4

Make sure all parts are moving smoothly. Make sure you tighten loose nuts and bolts. Your snow blower may vibrate during operation, causing nuts and bolts to loosen. Tighten those up to prevent them from falling off when your snow blower is in use.

Additionally, check to make sure belts and cables are in good condition. If you spot any damage, replace them. Any significant wear and tear call for a replacement to avoid the danger of a belt breaking during use.

After your snow blower is prepared for winter, start it up and let it run for a few minutes in a well-ventilated area to be certain everything works properly. Consider starting your machine every so often if it sits for an extended period.

Note: Not all snow blowers are the same. Different snow blowers utilize different types of fuel, oil and screws so consult your owner’s manual before repairing your equipment.

Free Parts Search - 4 Ways to Dispose of Leaves     Free Shipping - 4 Ways to Dispose of Leaves

How to Install a Mulch Kit on a Cub Cadet Tractor

How to Install a Mulch Kit on a Cub Cadet Tractor

A mulch kit is a way to convert your Cub Cadet tractor into a mulcher. When you change the tractor’s standard blades to mulching blades, the mulch kit recycles the lawn clippings as you mow and spreads them back onto your lawn. This returns nutrients back into the soil, keeping your grass healthy. Here’s how to install a mulch kit on your Cub Cadet tractor.

Depending on your model number, these instructions may vary.  Be sure to refer to your owner’s manual for detailed instructions, recommended maintenance and safety instructions.

Before performing any maintenance on your machine, engage the parking brake on a flat, level surface and remove the key from the ignition. Disconnect the spark plug wire to prevent accidental starting.

To install a mulch kit on a Cub Cadet tractor, begin by removing the mower deck. Set the deck height to its lowest setting. Pull the right idler pulley to release tension on the deck belt, and then ease the deck belt off the engine pulley.

Use pliers to remove the cotter pin from the front deck lift rod and slide the rod out of the hanger bracket. Remove the hairpin clip securing the right side of the deck to the hanger bracket supporting the cutting deck and release it from the hanger bracket by moving the deck outward and off the hanger rod making sure the deck doesn’t fall. Repeat this step on the left side and slide the deck out from underneath the tractor.

Once the mower deck is off, flip it over to access its underside to prepare to remove the old mower blades. Note: always wear heavy duty gloves when handling blades.

Use a block of wood and wedge it between the blade and the frame of the mower deck. Make sure it’s good and steady because you’ll be applying force. Remove the center holding nut from the mower blade with a wrench. Use a gloved hand to keep the blade from turning while removing the nut. Save the nut for installing the mulching blade. Repeat this blade removal step for the mower blade on the other side of the deck.

Once the old blades are removed, you can replace them with the new blades included in the mulch kit. Place the center hole of the mulching blade over the mounting stud on the underside of the mower deck. Make sure each blade with the side marked “bottom” or with the part number on it is facing the ground when the mower is in the operating position.

Use your gloved hand to hold the blade in place while tightening the holding nut with your wrench. Repeat this step to install the mulching blade on the other side of the deck as well.

To install the mulch plug on your Cub Cadet tractor, lift the discharge chute up. Place the mulch plug into the deck discharge chute by fitting the bolt on the rear side of the mulch plug into the hole in the deck.  Move the mulch plug into place, then pull and stretch the retaining plug on the mulch plug over the deck wheel bracket and hook it under the bottom of the bracket.

Slide the deck back under the tractor and reattach the deck. You are now ready to use your Cub Cadet tractor as a mulcher.

Free Parts Search - How to Change a Cub Cadet Walk Behind Lawn Mower Blade     Free Shipping - How to Change a Cub Cadet Walk Behind Lawn Mower Blade

How to Change a Cub Cadet Walk Behind Lawn Mower Blade

How to Change a Cub Cadet Walk Behind Lawn Mower Blade

Sharpening or changing your lawn mower blade is imperative to a well-manicured lawn. A lawn mower with a dull blade will cut the grass unevenly and the tips of grass blades will be torn instead of cleanly-sliced. Periodically inspect your lawn and lawn mower to determine if a new blade is needed. As a rule of thumb, sharpen or replace your lawn mower blade at least once a year. Refer to this guide when it’s time to change your .

Before performing any maintenance on your lawn mower, refer to your owner’s manual for maintenance instructions and safety information. Maintenance instructions vary by model, so depending on your lawn mower model our instructions may vary slightly.

Before changing the wheels on your lawn mower, please abide by these safety precautions:

  • Shut off the engine
  • Allow the engine to become cool to the touch
  • Disconnect the spark plug wire to prevent accidental starting

First, turn the mower on its side to access the blade. Make sure the air filter and carburetor side is facing up. Mower blades are sharp so make sure you always wear gloves for protection. Secure the lawn mower blade using a blade removal tool or place a block of wood between the blade and the frame of the mower to support the blade when you apply pressure to remove it.

Remove the blade retaining bolt and then remove the blade. Depending on wear and tear, either sharpen the blade or replace it with a new one. Secure the new or sharpened blade with the blade removal tool or block of wood. Then tighten the blade retaining bolt to the torque indicated in your owner’s manual.

The side of the blade that says “Bottom,” or shows the part number should face the ground when the mower is in operating position. Once the blade is secured on your lawn mower, turn the lawn mower right side up and reconnect the spark plug. Start your lawn mower and listen for noises or vibration.

Free Parts Search - How to Change a Cub Cadet Walk Behind Lawn Mower Blade     Free Shipping - How to Change a Cub Cadet Walk Behind Lawn Mower Blade